切换到宽版
  • 5503阅读
  • 11回复

[求助]特急﹗﹗ dek265,視覺系統有問題﹗﹗ [复制链接]

上一主题 下一主题
离线hou
在线等级:8
在线时长:504小时
升级剩余时间:36小时在线等级:8
在线时长:504小时
升级剩余时间:36小时
级别:一般会员
 
金币
1840
威望
5
贡献
2
好评
0
注册
2003-05-20
只看楼主 倒序阅读 使用道具 楼主  发表于: 2004-04-20
dek265gs,在機器找mark時相驅動馬達卡到軌道﹐觀察了一下table在上升清楚照到mark后還繼續上升。該如何設定高度值﹐請教各位專家﹗﹗
分享到
离线Dekker
在线等级:18
在线时长:1920小时
升级剩余时间:170小时在线等级:18
在线时长:1920小时
升级剩余时间:170小时在线等级:18
在线时长:1920小时
升级剩余时间:170小时
级别:资深会员

金币
629
威望
43
贡献
23
好评
17
注册
2004-02-09
只看该作者 沙发  发表于: 2004-04-21
诊断---rising table---vision heigh---adjust,再用一把直尺去量table表面到钢网框架底部之距离,有一个确切的数值,一下想不起来了,去查mannul吧,照这个数值调整即可!
离线Dekker
在线等级:18
在线时长:1920小时
升级剩余时间:170小时在线等级:18
在线时长:1920小时
升级剩余时间:170小时在线等级:18
在线时长:1920小时
升级剩余时间:170小时
级别:资深会员

金币
629
威望
43
贡献
23
好评
17
注册
2004-02-09
只看该作者 藤椅  发表于: 2004-04-21
1. Open the front cover.
2. Fit a stencil into the chase and slide to the rear, so that the front edge of the
screen is further back than the front edge of the rising table, (figure below
refers).
3. Close the front cover.
4. In Diagnostics select the Screen Change module. Select Toggle Screen
Clamps.
5. In Diagnostics select the Rising Table module. Select Home Rising Table.
6. Open the front cover.
7. Check that the distance from the top of the tooling table to the underside of
the screen is 208mm - 210mm (168mm - 170mm with AutoFlex tooling
fitted).
8. If the setting is correct either remove or home the screen. If adjustment is
necessary carry out Rising Table Home Adjustment.
这是调整table的home高度,vision高度调整也是大同小异!
离线Dekker
在线等级:18
在线时长:1920小时
升级剩余时间:170小时在线等级:18
在线时长:1920小时
升级剩余时间:170小时在线等级:18
在线时长:1920小时
升级剩余时间:170小时
级别:资深会员

金币
629
威望
43
贡献
23
好评
17
注册
2004-02-09
只看该作者 板凳  发表于: 2004-04-21
Restore Default Heights

Selecting this diagnostic function restores the vision height to the default of 50
mm and the print height to the default of 127 mm.

Set Reference Vision Height

Selecting this diagnostic function enables the rising table vision height to be set
so that the camera views the board fiducials in focus. This is achieved by driving
the table up or down while viewing the vision monitor until the fiducial is in
focus. Pressing Calibrate Vision Height changes the menu Bar showing the
option Confirm. Pressing Confirm sets the current height of the rising table,
updating the printer configuration file. Refer to the Technical Reference Manual,
Camera and Vision System chapter for the camera reference position procedure.
离线hou
在线等级:8
在线时长:504小时
升级剩余时间:36小时在线等级:8
在线时长:504小时
升级剩余时间:36小时
级别:一般会员
金币
1840
威望
5
贡献
2
好评
0
注册
2003-05-20
只看该作者 报纸  发表于: 2004-04-22
^道謝
非常感謝﹗﹗可以再詳細一點嗎﹖進入adjust后它不顯示度高度單位﹐而出現cycle time 50S﹐是不是還有進入順序才能設定。能否告知﹖﹖﹖
best regards!!
离线eastar510
在线等级:1
在线时长:42小时
升级剩余时间:8小时
级别:中级会员
金币
56
威望
7
贡献
1
好评
2
注册
2004-03-07
只看该作者 地板  发表于: 2004-04-28
VISION高度校正怎么样的?那天我去校正它的时候,没有成功.它和TABLE的高度校正好像不同.TABLE高度已校正OK.校正VISION的时候具体的步骤是怎么样的??????????
离线tanktian
级别:新手实习

金币
827
威望
3
贡献
2
好评
0
注册
2004-05-06
只看该作者 地下室  发表于: 2004-05-10
1. Switch on the machine and insert the maintenance key. Turn the maintenance key to
the On position.
Diagnost
2. Select Diagnost and press the System button. Fiducial training takes place.
3. From the Module Diagnostic Page select Camera Axes. The rising table moves to
the home position.
4. Select Home Camera X Axis. Select Home Camera Y Axis. The camera homes in
the X and Y axes.
5. Place a board onto the rails and slide it into a central position.
6. Select Move Camera Axis to Reference Position.
7. Select Exit. Select Rising Table Diagnostic.
8. Select Home Rising Table.
9 Select Raise Table to Vision Height.
10. Insert the product screen.
11. With a metric rule, measure the distance from the underside of the screen to the top
surface of the board.
12. Select Drive Table Using Jog Buttons.
CAUTION
VISION HEIGHT. The rising table must not be jogged up higher than the
specified dimension (less than 78.0mm) or camera damage may occur.
13. Pressing the appropriate jog button, carefully jog the rising table in the required
direction until the dimension 78.0mm +2.0mm -0.0mm exists between board and
screen Figure 10-14 refers, whilst aiming for optimum focus on the reference
position.
离线beauty_dev
级别:*
金币
*
威望
*
贡献
*
好评
0
注册
*
只看该作者 7楼 发表于: 2004-05-12
能用中文翻译吗
看完你这段翻译,也要花上少少时间
主要是讲钢网到板的距离是78MM吧?
离线tanktian
级别:新手实习

金币
827
威望
3
贡献
2
好评
0
注册
2004-05-06
只看该作者 8楼 发表于: 2004-05-13
请依下列进行:Maint.(F8)----Diagnostic (F6)-----选择Rising Table ----选择并执行Home Rising Table-----选择并执行Raise Table to Vision Height----装一钢网(不固定)-----在轨道上放一PCB,用一钢尺测量钢网下表面到PCB上表面的距离(大于78mm),如果不是,选择并执行 Drive Table Using Jog Buttons---用两个机器前端控制抬头的按钮中的一个驱动Table 上升或下降,使得用一钢尺测量钢网下表面到PCB上表面的距离大于78mm---选择并执行Set Raise Table Vision Height----完成调整。
离线eastar510
在线等级:1
在线时长:42小时
升级剩余时间:8小时
级别:中级会员
金币
56
威望
7
贡献
1
好评
2
注册
2004-03-07
只看该作者 9楼 发表于: 2004-05-14
谢谢楼上的帮助.我是在使用两个控制键来让TABLE上升的时候高度值出了错,所以没有成功.是否必须要大于78mm才行?小于78mm不行吗?TABLE的印刷高度也可以 加大加小啊!!!!!!!!!!
离线beauty_dev
级别:*
金币
*
威望
*
贡献
*
好评
0
注册
*
只看该作者 10楼 发表于: 2004-05-15
应该是太高了怕撞到camera吧
离线tanktian
级别:新手实习

金币
827
威望
3
贡献
2
好评
0
注册
2004-05-06
只看该作者 11楼 发表于: 2004-05-15
、、
[QUOTE]最初由 eastar510 发表
[B]谢谢楼上的帮助.我是在使用两个控制键来让TABLE上升的时候高度值出了错,所以没有成功.是否必须要大于78mm才行?小于78mm不行吗?TABLE的印刷高度也可以 加大加小啊!!!!!!!!!! [/B][/QUOTE]


  应大于78mm,但你要注意不能太高,否则会撞到相机的。