[求助] [问题] 优化软件HLC 请大家翻译一句话　　 [复制链接]

Execute tact simulation and feed back division.
Feedback loop will be repeated until either the max loop count or target difference time is achieved whichever comes first. 这一栏不明白其确切的意思。

hi,frind:
  You known the HLC software,I have a question about it,I think to confirm that it can convert the ASCII CAD to binary format(730/740 format<*.G3C,*.G3G>),Give a help,thanks!

有一个flexprog.exe程式，将ASCII转为hlc(*.g2h).
在HLC优化成功后生成*.h4h,*h41,*h42,不要在HLC中另存为*.g3g,*.g3c,要在桌面上重新命名，否则feeder号看不到。

hi,firable:
  Thank you for your good reply!
  I can convert the ascii file to *.g2h or *.g2c or *.g2g,Can 730/740 read the format,or read the file by 710/720, at first,then copy the file to the other format of 730/740,or can you left your tel number,I think to detail about it,thanks a lot!

*.h4h不要改為*.g3c,我今天刚试过，在机器上看不到Feeder号。
我觉得hlc这个软件不是很好 用，我在用时常有这样的现象：当优化结束，开始执行tact时，提示"当x,y轴移动时程序出现错误 " ，就肯定有一台机器的程式没优化成，但在机器上可以运行，我找了好久没找到原因。也有优化成功的，就是板上的元件种类很少，基本上是R,C,RN,SOT23.

hi,firable:
  I am happy that I see you at this place!
  Now I only have the "flexprog.exe",Can you tell me how to convert the ascii file to 730/740 format,thank you very much!

only have the "flexprog.exe",转化后的file并没有告诉机器所用料的（part data), 用什么head ,nozzle ,feeder号( pick data)。
不知你是因为没有hlc,还是使用hlc中碰到了问题？
我做的是750，760是这样的：
如果程式优化和tact都通过了，会有相应的*.h41,*h42,*h43,*h44,*h45档的生成，不要在HLC中另存为*.g3g,*.g3c,要在桌面上重新命名。

hi,firable:
  I can only convert the ascii file to binary format by "flexprog.exe",I don't optimize the program,I only need the binary format file,if you don't understand my mean,can you left the tel number,I contact you,thanks!

Covsion type:   选 ascii->hlc，后再按enter.
field delimeter: space
ascii file:       c:\windows\desktop\*.cad
hlc file:         c:\windows\desktop\*.g2h
units:         mm
board view:     top
board rotation: 0
rotation units ：degrees
pwb type；single
boc mark type:each pwb
                        pwb       fields

1:none   2:none   3:none   4:none   5:none
          placement field ordering
1:comp id     2:x coord   3:y coord   4:rotation   5:comp name

Execute tact simulation and feed back division.
Feedback loop will be repeated until either the max loop count or target difference time is achieved whichever comes first.

以上这句话意思是说：
执行智能模拟和反馈分割程序。
反馈循环将重复，直到达到最大循环数（Max Loop）或目标差异时间（Target difference ）设置值的某一项要求才停止。

也就是说，你在优化（Optimazation）选项的Feed Back标签中两个参数值Max Loop和Target difference 只要其中之一达到，优化才会结束。

Target difference 不要设得太长。