SMT之家论坛 -> ASSEMBLEON 安必昂贴片机 -> FCMI校准问题，请高手帮助！ 登录 -> 注册 -> 回复主题 -> 发表主题


菰獨寳貝 2008-05-10 07:52
我司在转拉时出现这样的问题
1.正规的PCB板，L；124   W;102.8
2.用的180间距做的程式

问题是：
在做CLC之前做不出生产测试板的文件，但将长改为130以上。再次就可以生成了
在FCMII上要将长改到134以上才可以

请问高手这是什么情况，是机器设置问题吗
还是什么别的问题？

期待你的指点，谢谢。

菰獨寳貝 2008-05-14 01:29
是我写的不清楚，还是没有高手帮助？

版主也该了表一下意见嘛！

菰獨寳貝 2008-05-15 07:58
版主辞职不干了吗

做FCM的没高手了吗

sunnyzeng 2008-05-17 14:53
这个和机器的设置是没有关系的,你做CLC程序前把程序里的板长改短一些就好啦.做出来的CLC程序就是按你程序内的长度做出来的.

菰獨寳貝 2008-05-18 03:01
就是按实际的长做不出来
才改长的，改长了可以做

sxp 2008-05-20 06:52
是有这样的情况，好象是长和宽要在一定的比例之内才能生成CLC校正文件。

峰之梦 2008-05-20 23:44
我这也试过~~做CKS的时候也会这样~~~本人不明白

菰獨寳貝 2008-05-22 10:35
我做CKS没问题的，就是生成ASP和PBI文件时生不成

sunnyzeng 2008-05-24 09:48
124板长的,程序做出来的index是:INDEX1:60 , INDEX2:70 ,BVM程序也一样.
1,检查你程序里面的INDEX是多少.
2,检查你BVM程序的INDEX是多少.
3,这两个程序的INDEX必须一样才能生产.
4,如果你要改成180的INDEX生产,必须把板长改长一些(你将板长改到165重新优化程序,BVM程序也一样,将板长改为165.保证BVM程序和贴片程序的INDEX一样,肯定可以生产.

菰獨寳貝 2008-05-30 23:05
我明白，
但是、生成ASP和PBI这两个文件和BVM文件没什么关系的
用180PITCH我试做了一下CKS显示INDEX三个全是60（BVM)

sunnyzeng 2008-06-04 14:28
3 个60的INDEX是正常的呀.程序中的index是多少?

菰獨寳貝 2008-06-07 23:59
也是的啊
是一个样的

菰獨寳貝 2008-06-08 00:03
index不是问题
我说过将板长改长过就可以了
如果index不对的话，我们将板长改长也是不行嘛

sunnyzeng 2008-06-09 10:55
将程序传上来,可以一起分析一下.

菰獨寳貝 2008-06-16 18:54
COMMENT
COMMENT Action spec generated with PPS RELEASE : CB
COMMENT


COMMENT
COMMENT TEMPORARY ADAPTIONS OF THIS ACTION SPEC
COMMENT

COMMENT Blanks in identifiers are replaced by a: _
COMMENT Truncated identifiers always end with a: @


AS GENERAL
COMMENT
COMMENT General Actions
COMMENT

SYNTAX   2
CREATOR   FABmaster
FILE_ID   FCMB1-1.ASC
LINE_ID   XXXXXXXX
MACH_ID   FCMB1
MACH_ADDR 3
ISSUEDATE 2007-12-6


AS PRODUCT
COMMENT
COMMENT Product actions
COMMENT

PROD_ID A7686MBTOP2+
SIDE   T
FAMILY A7686MBTOP2+
BOARD_ROTATION     0
BOARD_DIM       124.000 102.800   3.000
STOPPER       -261.000
BOARD_PITCH     180.000
NUMBER_OF_BOARDS   13
CYCLE_TIME       18.029


AS TC
COMMENT
COMMENT Transport actions
COMMENT

LIFTUP -440.000

COMMENT step/value
STEP     1   60.000
STEP     2   60.000
STEP     3   60.000
AS BVM
COMMENT
COMMENT Board Vision Module actions
COMMENT

BOARD_ROTATION   0

COMMENT index coordinates are relative to machine origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   1 -206.000 143.000 -201.000 138.000
INDEX     2   1 -146.000 143.000 -141.000 138.000
INDEX     3   1 -86.000 143.000 -81.000 138.000

FID_ALG   2_PNT_STRETCH

COMMENT coordinates are in board coordinates
COMMENT [number] type indx brd attr pos_x pos_y [circ_nrs]
FIDUCIAL   1 1 1 1 N -10.000   5.000
FIDUCIAL   2 1 1 1 N -114.000   97.800

AS LAS   1
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0ER00004165YA   RR_0402  
FEEDER   2 1 T8-M/2           T   XBR0ER10404165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   3 154.000 143.000 159.000 138.000
INDEX     2   2   34.000 143.000   39.000 138.000
INDEX     2   3 214.000 143.000 219.000 138.000
INDEX     3   2   94.000 143.000   99.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT R611         2 1 3 1 1   -79.079   43.485   270.0   0.0
MOUNT J600         1 1 3 1 1 -121.079   39.954   270.0   0.0
MOUNT R216         2 1 3 2 1   -62.950   31.826   0.0   0.0
MOUNT R215         1 1 3 2 1   -99.997   32.029   0.0   0.0
MOUNT R402         1 1 3 2 1   -98.168   27.610   0.0   0.0
MOUNT R523         3 2 2 1 1   -16.479   20.244   270.0   0.0
MOUNT R611         1 2 3 1 1 -121.079   43.485   270.0   0.0
MOUNT R215         3 2 2 2 1   -15.997   32.029   0.0   0.0
MOUNT R503         1 2 3 2 1 -122.959   25.806   270.0   0.0
MOUNT J600         3 3 2 1 1   -37.079   39.954   270.0   0.0
MOUNT R524         2 3 2 1 1   -57.845   17.094   0.0   0.0
MOUNT R402         5 3 2 2 1   -56.168   70.410   0.0   0.0
MOUNT R215         2 3 2 2 1   -57.997   32.029   0.0   0.0
MOUNT R216         3 3 2 2 1   -20.950   31.826   0.0   0.0
MOUNT R503         3 3 2 2 1   -38.958   25.806   270.0   0.0

AS LAS   2
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   2 1 T8-M/2           T   XBR0EC47004505TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   3   34.000 143.000   39.000 138.000
INDEX     2   3   94.000 143.000   99.000 138.000
INDEX     3   3 154.000 143.000 159.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C216         6 1 3 2 1   -18.029   76.379   0.0   0.0
MOUNT C278         5 2 3 2 1   -68.513   78.258   180.0   0.0
MOUNT C232         5 2 3 2 1   -62.442   76.125   270.0   0.0
MOUNT C277         2 2 3 2 1   -69.097   34.011   90.0   0.0
MOUNT C277         6 2 3 2 1   -27.097   76.811   90.0   0.0
MOUNT C277         3 2 3 2 1   -27.097   34.011   90.0   0.0
MOUNT C216         4 3 3 2 1 -102.029   76.379   0.0   0.0
MOUNT C277         4 3 3 2 1 -111.097   76.811   90.0   0.0
MOUNT C277         1 3 3 2 1 -111.097   34.011   90.0   0.0
MOUNT C232         1 3 3 2 1 -104.442   33.325   270.0   0.0
MOUNT C216         5 3 3 2 1   -60.029   76.379   0.0   0.0
MOUNT C278         2 3 3 2 1   -68.513   35.458   180.0   0.0

AS LAS   3
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   2 1 T8-M/2           T   XBR0EC47004505TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   4   94.000 143.000   99.000 138.000
INDEX     2   4 154.000 143.000 159.000 138.000
INDEX     3   3   34.000 143.000   39.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C277         5 1 4 2 1   -69.097   76.811   90.0   0.0
MOUNT C232         2 1 4 2 1   -62.442   33.325   270.0   0.0
MOUNT C278         6 1 4 2 1   -26.513   78.258   180.0   0.0
MOUNT C232         6 1 4 2 1   -20.442   76.125   270.0   0.0
MOUNT C278         3 1 4 2 1   -26.513   35.458   180.0   0.0
MOUNT C232         3 1 4 2 1   -20.442   33.325   270.0   0.0
MOUNT C278         4 2 4 2 1 -110.513   78.258   180.0   0.0
MOUNT C232         4 2 4 2 1 -104.442   76.125   270.0   0.0
MOUNT C278         1 2 4 2 1 -110.513   35.458   180.0   0.0
MOUNT C216         1 2 4 2 1 -102.029   33.579   0.0   0.0
MOUNT C216         2 2 4 2 1   -60.029   33.579   0.0   0.0
MOUNT C216         3 3 3 2 1   -18.029   33.579   0.0   0.0

AS LAS   4
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10104505TD   C_0402  
FEEDER   2 1 T8-M/2           T   XBR0ER10404165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   5 154.000 143.000 159.000 138.000
INDEX     2   4   34.000 143.000   39.000 138.000
INDEX     3   4   94.000 143.000   99.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT R503         5 1 5 2 1   -80.959   68.606   270.0   0.0
MOUNT R216         1 1 5 2 1 -104.950   31.826   0.0   0.0
MOUNT R503         2 1 5 2 1   -80.959   25.806   270.0   0.0
MOUNT T205         1 1 5 1 1   -94.892   36.043   90.0   0.0
MOUNT T204         1 1 5 1 1   -89.126   35.662   180.0   0.0
MOUNT R402         3 2 4 2 1   -14.168   27.610   0.0   0.0
MOUNT C270         6 2 4 1 1   -8.453   78.208   180.0   0.0
MOUNT C270         3 2 4 1 1   -8.453   35.408   180.0   0.0
MOUNT R402         2 3 4 2 1   -56.168   27.610   0.0   0.0
MOUNT T204         5 3 4 1 1   -47.126   78.462   180.0   0.0
MOUNT T205         2 3 4 1 1   -52.892   36.043   90.0   0.0
MOUNT T204         2 3 4 1 1   -47.126   35.662   180.0   0.0
MOUNT T205         6 3 4 1 1   -10.892   78.843   90.0   0.0

AS LAS   5
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10304256TD   C_0402  
FEEDER   2 1 T8-M/2           T   XBR0EC22004505TD   C_0402  
FEEDER   5 1 T8-M/2           T   XBR0ER39204165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   5   34.000 143.000   39.000 138.000
INDEX     1   6 214.000 143.000 219.000 138.000
INDEX     2   5   94.000 143.000   99.000 138.000
INDEX     3   5 154.000 143.000 159.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80
PICK   5 1   1   1   83.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C228         6 1 5 1 1   -18.029   75.642   0.0   0.0
MOUNT C620         1 1 6 2 1 -121.079   34.315   270.0   0.0
MOUNT C273         5 2 5 1 1   -62.950   77.573   0.0   0.0
MOUNT C228         5 2 5 1 1   -60.029   75.642   0.0   0.0
MOUNT C620         2 2 5 2 1   -79.079   34.315   270.0   0.0
MOUNT R405         6 2 5 5 1   -28.646   72.874   270.0   0.0
MOUNT R405         3 2 5 5 1   -28.646   30.074   270.0   0.0
MOUNT C228         1 3 5 1 1 -102.029   32.842   0.0   0.0
MOUNT C273         2 3 5 1 1   -62.950   34.773   0.0   0.0
MOUNT R405         4 3 5 5 1 -112.646   72.874   270.0   0.0
MOUNT R405         1 3 5 5 1 -112.646   30.074   270.0   0.0
MOUNT R405         5 3 5 5 1   -70.646   72.874   270.0   0.0
MOUNT R405         2 3 5 5 1   -70.646   30.074   270.0   0.0

AS LAS   6
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10104505TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   6   94.000 143.000   99.000 138.000
INDEX     2   6 154.000 143.000 159.000 138.000
INDEX     3   5   34.000 143.000   39.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C270         5 1 6 1 1   -50.453   78.208   180.0   0.0
MOUNT T205         5 1 6 1 1   -52.892   78.843   90.0   0.0
MOUNT C270         2 1 6 1 1   -50.453   35.408   180.0   0.0
MOUNT T204         6 1 6 1 1   -5.126   78.462   180.0   0.0
MOUNT T204         3 1 6 1 1   -5.126   35.662   180.0   0.0
MOUNT C270         4 2 6 1 1   -92.453   78.208   180.0   0.0
MOUNT T204         4 2 6 1 1   -89.126   78.462   180.0   0.0
MOUNT T205         4 2 6 1 1   -94.892   78.843   90.0   0.0
MOUNT C270         1 2 6 1 1   -92.453   35.408   180.0   0.0
MOUNT T205         3 3 5 1 1   -10.892   36.043   90.0   0.0

AS LAS   7
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   2 1 T8-M/2           T   XBR0EC50004050AM   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   7 154.000 143.000 159.000 138.000
INDEX     2   6   34.000 143.000   39.000 138.000
INDEX     2   7 214.000 143.000 219.000 138.000
INDEX     3   6   94.000 143.000   99.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT T210         2 1 7 2 1   -68.513   32.563   180.0   0.0
MOUNT T505         2 1 7 2 1   -75.980   20.320   0.0   0.0
MOUNT T301         1 1 7 2 1   -87.068   34.188   0.0   0.0
MOUNT T501         1 1 7 2 1 -118.082   26.772   270.0   0.0
MOUNT T503         2 1 7 2 1   -81.467   20.676   90.0   0.0
MOUNT T302         3 2 6 2 1   -1.620   42.977   180.0   0.0
MOUNT T300         3 2 6 2 1   -2.205   35.814   270.0   0.0
MOUNT T504         1 2 7 2 1 -120.012   20.320   180.0   0.0
MOUNT T503         1 2 7 2 1 -123.467   20.676   90.0   0.0
MOUNT T210         3 3 6 2 1   -26.513   32.563   180.0   0.0
MOUNT T505         3 3 6 2 1   -33.980   20.320   0.0   0.0
MOUNT T504         3 3 6 2 1   -36.012   20.320   180.0   0.0
MOUNT T503         3 3 6 2 1   -39.466   20.676   90.0   0.0
MOUNT T211         2 3 6 2 1   -75.980   35.611   0.0   0.0
MOUNT T501         2 3 6 2 1   -76.082   26.772   270.0   0.0

AS LAS   8
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10304256TD   C_0402  
FEEDER   2 1 T8-M/2           T   XBR0EC22004505TD   C_0402  
FEEDER   3 1 T8-M/2           T   XBR0ER10304165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   7   34.000 143.000   39.000 138.000
INDEX     2   7   94.000 143.000   99.000 138.000
INDEX     3   7 154.000 143.000 159.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80
PICK   3 1   1   1   51.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C228         3 1 7 1 1   -18.029   32.842   0.0   0.0
MOUNT R521         6 1 7 3 1   -17.876   59.970   0.0   0.0
MOUNT R522         6 1 7 3 1   -19.934   59.970   0.0   0.0
MOUNT R522         3 1 7 3 1   -19.934   17.170   0.0   0.0
MOUNT C228         2 2 7 1 1   -60.029   32.842   0.0   0.0
MOUNT C273         6 2 7 1 1   -20.950   77.573   0.0   0.0
MOUNT C273         3 2 7 1 1   -20.950   34.773   0.0   0.0
MOUNT C620         3 2 7 2 1   -37.079   34.315   270.0   0.0
MOUNT R522         2 2 7 3 1   -61.934   17.170   0.0   0.0
MOUNT C273         4 3 7 1 1 -104.950   77.573   0.0   0.0
MOUNT C228         4 3 7 1 1 -102.029   75.642   0.0   0.0
MOUNT C273         1 3 7 1 1 -104.950   34.773   0.0   0.0
MOUNT R521         4 3 7 3 1 -101.877   59.970   0.0   0.0
MOUNT R521         1 3 7 3 1 -101.877   17.170   0.0   0.0
MOUNT R522         5 3 7 3 1   -61.934   59.970   0.0   0.0

AS LAS   9
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0ER00004165YA   RR_0402  
FEEDER   4 1 T8-M/2           T   XBR0EC18004505TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   8   94.000 143.000   99.000 138.000
INDEX     2   8 154.000 143.000 159.000 138.000
INDEX     3   7   34.000 143.000   39.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   4 1   1   1   67.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT R524         5 1 8 1 1   -57.845   59.894   0.0   0.0
MOUNT R611         3 1 8 1 1   -37.079   43.485   270.0   0.0
MOUNT R523         2 1 8 1 1   -58.480   20.244   270.0   0.0
MOUNT J600         2 1 8 1 1   -79.079   39.954   270.0   0.0
MOUNT C279         3 1 8 4 1   -31.948   35.230   0.0   0.0
MOUNT R524         4 2 8 1 1   -99.845   59.894   0.0   0.0
MOUNT R523         1 2 8 1 1 -100.480   20.244   270.0   0.0
MOUNT C279         4 2 8 4 1 -115.948   78.030   0.0   0.0
MOUNT C279         5 2 8 4 1   -73.948   78.030   0.0   0.0
MOUNT C279         2 2 8 4 1   -73.948   35.230   0.0   0.0
MOUNT R524         3 3 7 1 1   -15.844   17.094   0.0   0.0

AS LAS   10
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   2 1 T8-M/2           T   XBR0EC50004050AM   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   9 154.000 143.000 159.000 138.000
INDEX     2   8   34.000 143.000   39.000 138.000
INDEX     2   9 214.000 143.000 219.000 138.000
INDEX     3   8   94.000 143.000   99.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT T302         1 1 9 2 1   -85.621   42.977   180.0   0.0
MOUNT T300         1 1 9 2 1   -86.205   35.814   270.0   0.0
MOUNT T211         1 1 9 2 1 -117.980   35.611   0.0   0.0
MOUNT T210         1 1 9 2 1 -110.513   32.563   180.0   0.0
MOUNT T502         2 1 9 2 1   -80.705   20.676   90.0   0.0
MOUNT T505         1 1 9 2 1 -117.980   20.320   0.0   0.0
MOUNT T301         3 2 8 2 1   -3.068   34.188   0.0   0.0
MOUNT T502         1 2 9 2 1 -122.705   20.676   90.0   0.0
MOUNT T302         2 3 8 2 1   -43.621   42.977   180.0   0.0
MOUNT T211         3 3 8 2 1   -33.980   35.611   0.0   0.0
MOUNT T300         2 3 8 2 1   -44.205   35.814   270.0   0.0
MOUNT T301         2 3 8 2 1   -45.069   34.188   0.0   0.0
MOUNT T501         3 3 8 2 1   -34.082   26.772   270.0   0.0
MOUNT T502         3 3 8 2 1   -38.704   20.676   90.0   0.0
MOUNT T504         2 3 8 2 1   -78.012   20.320   180.0   0.0

AS LAS   11
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10504636TD   C_0402  
FEEDER   3 1 T8-M/2           T   XBR0ER20304165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1   9   34.000 143.000   39.000 138.000
INDEX     1 10 214.000 143.000 219.000 138.000
INDEX     2   9   94.000 143.000   99.000 138.000
INDEX     3   9 154.000 143.000 159.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   3 1   1   1   51.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C275         3 1 9 1 1   -18.842   30.175   90.0   0.0
MOUNT C505         1 1 10 1 1 -122.959   27.838   90.0   0.0
MOUNT R210         3 1 9 3 1   -18.029   32.029   0.0   0.0
MOUNT R213         5 2 9 3 1   -63.458   76.125   90.0   0.0
MOUNT R210         5 2 9 3 1   -60.029   74.829   0.0   0.0
MOUNT R213         2 2 9 3 1   -63.458   33.325   90.0   0.0
MOUNT R239         2 2 9 3 1   -62.493   28.016   0.0   0.0
MOUNT R213         3 2 9 3 1   -21.458   33.325   90.0   0.0
MOUNT R213         4 3 9 3 1 -105.458   76.125   90.0   0.0
MOUNT R210         4 3 9 3 1 -102.029   74.829   0.0   0.0
MOUNT R239         4 3 9 3 1 -104.493   70.816   0.0   0.0
MOUNT R210         1 3 9 3 1 -102.029   32.029   0.0   0.0
MOUNT R239         5 3 9 3 1   -62.493   70.816   0.0   0.0
MOUNT R210         2 3 9 3 1   -60.029   32.029   0.0   0.0

AS LAS   12
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10504636TD   C_0402  
FEEDER   4 1 T8-M/2           T   XBR0EC18004505TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1 10   94.000 143.000   99.000 138.000
INDEX     2 10 154.000 143.000 159.000 138.000
INDEX     3   9   34.000 143.000   39.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   4 1   1   1   67.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C279         6 1 10 4 1   -31.948   78.030   0.0   0.0
MOUNT C511         3 1 10 1 1   -29.408   30.074   90.0   0.0
MOUNT C226         2 1 10 1 1   -58.073   28.423   180.0   0.0
MOUNT C505         3 1 10 1 1   -38.958   27.838   90.0   0.0
MOUNT C275         2 1 10 1 1   -60.842   30.175   90.0   0.0
MOUNT C511         2 1 10 1 1   -71.408   30.074   90.0   0.0
MOUNT C279         1 2 10 4 1 -115.948   35.230   0.0   0.0
MOUNT C275         1 2 10 1 1 -102.842   30.175   90.0   0.0
MOUNT C511         1 2 10 1 1 -113.408   30.074   90.0   0.0
MOUNT C226         1 2 10 1 1 -100.073   28.423   180.0   0.0
MOUNT C505         2 2 10 1 1   -80.959   27.838   90.0   0.0
MOUNT C226         3 3 9 1 1   -16.073   28.423   180.0   0.0

AS LAS   13
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10404106TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1 11 154.000 143.000 159.000 138.000
INDEX     2 10   34.000 143.000   39.000 138.000
INDEX     3 10   94.000 143.000   99.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C274         4 1 11 1 1 -106.118   72.975   270.0   0.0
MOUNT C111         4 1 11 1 1   -99.591   69.521   90.0   0.0
MOUNT C502         4 1 11 1 1 -113.205   62.206   180.0   0.0
MOUNT C111         1 1 11 1 1   -99.591   26.721   90.0   0.0
MOUNT C109         1 1 11 1 1   -98.194   23.292   270.0   0.0
MOUNT C520         6 2 10 1 1   -15.844   61.418   180.0   0.0
MOUNT C227         3 2 10 1 1   -14.193   29.896   0.0   0.0
MOUNT C104         3 2 10 1 1   -14.168   26.873   0.0   0.0
MOUNT C111         3 2 10 1 1   -15.590   26.721   90.0   0.0
MOUNT C520         3 2 10 1 1   -15.844   18.618   180.0   0.0
MOUNT C503         6 3 10 1 1   -27.376   63.298   180.0   0.0
MOUNT C109         2 3 10 1 1   -56.194   23.292   270.0   0.0
MOUNT C502         3 3 10 1 1   -29.205   19.406   180.0   0.0
MOUNT C521         2 3 10 1 1   -57.845   17.856   180.0   0.0
MOUNT C274         5 3 10 1 1   -64.118   72.975   270.0   0.0
MOUNT C503         5 3 10 1 1   -69.376   63.298   180.0   0.0

AS LAS   14
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0ER10204165YA   RR_0402  
FEEDER   2 1 T8-M/2           T   XBR0ER20304165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1 11   34.000 143.000   39.000 138.000
INDEX     2 11   94.000 143.000   99.000 138.000
INDEX     3 11 154.000 143.000 159.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT R210         6 1 11 2 1   -18.029   74.829   0.0   0.0
MOUNT R213         6 2 11 2 1   -21.458   76.125   90.0   0.0
MOUNT R239         6 2 11 2 1   -20.493   70.816   0.0   0.0
MOUNT R239         3 2 11 2 1   -20.493   28.016   0.0   0.0
MOUNT R136         6 2 11 1 1   -24.100   61.037   270.0   0.0
MOUNT R136         3 2 11 1 1   -24.100   18.237   270.0   0.0
MOUNT R213         1 3 11 2 1 -105.458   33.325   90.0   0.0
MOUNT R239         1 3 11 2 1 -104.493   28.016   0.0   0.0
MOUNT R135         4 3 11 1 1 -108.862   60.428   270.0   0.0
MOUNT R135         1 3 11 1 1 -108.862   17.628   270.0   0.0
MOUNT R135         5 3 11 1 1   -66.862   60.428   270.0   0.0

AS LAS   15
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0ER10204165YA   RR_0402  
FEEDER   2 1 T8-M/2           T   XBR0ER10304165YA   RR_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1 12   94.000 143.000   99.000 138.000
INDEX     2 12 154.000 143.000 159.000 138.000
INDEX     3 11   34.000 143.000   39.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80
PICK   2 1   1   1   35.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT R521         5 1 12 2 1   -59.877   59.970   0.0   0.0
MOUNT R521         2 1 12 2 1   -59.877   17.170   0.0   0.0
MOUNT R136         5 1 12 1 1   -66.100   61.037   270.0   0.0
MOUNT R135         2 1 12 1 1   -66.862   17.628   270.0   0.0
MOUNT R135         6 1 12 1 1   -24.861   60.428   270.0   0.0
MOUNT R135         3 1 12 1 1   -24.861   17.628   270.0   0.0
MOUNT R522         4 2 12 2 1 -103.934   59.970   0.0   0.0
MOUNT R522         1 2 12 2 1 -103.934   17.170   0.0   0.0
MOUNT R136         4 2 12 1 1 -108.100   61.037   270.0   0.0
MOUNT R136         1 2 12 1 1 -108.100   18.237   270.0   0.0
MOUNT R136         2 2 12 1 1   -66.100   18.237   270.0   0.0
MOUNT R521         3 3 11 2 1   -17.876   17.170   0.0   0.0

AS LAS   16
COMMENT
COMMENT Placement module actions for position 1
COMMENT

COMMENT PPU_id   /nozzle_id       /clow/chgh/cidx
MUP     PIP/LA   4700             20   22   1

BOARD_ROTATION 0
COMMENT   fd/pk /feeder_id       /type /component_id     /pipla_id
FEEDER   1 1 T8-M/2           T   XBR0EC10404106TD   C_0402  

COMMENT index coordinates are relative to pipette origin
COMMENT indx/brd /refholex/refholey/board_x /board_y
INDEX     1 13 154.000 143.000 159.000 138.000
INDEX     2 12   34.000 143.000   39.000 138.000
INDEX     3 12   94.000 143.000   99.000 138.000

COMMENT pick coordinates are relative to pipette origin
COMMENT fd/pk/psh/rfp/pick_x /pick_y /pick_phi/na/prf/arf/ale/ple
PICK   1 1   1   1   19.000   77.000   90.0 1 95 95 100 80

COMMENT : In case a deviating dump postion is needed enter
COMMENT : DUMP postion_x position_y

COMMENT mount coordinates are in board coordinates
COMMENT comp_ref    /ci/ix/bd/fd/pk /mnt_x   /mnt_y/ /mnt_phi /align_phi
MOUNT C103         4 1 13 1 1   -96.746   69.521   270.0   0.0
MOUNT C104         4 1 13 1 1   -98.168   69.673   0.0   0.0
MOUNT C503         4 1 13 1 1 -111.376   63.298   180.0   0.0
MOUNT C274         1 1 13 1 1 -106.118   30.175   270.0   0.0
MOUNT C503         1 1 13 1 1 -111.376   20.498   180.0   0.0
MOUNT C521         1 1 13 1 1   -99.845   17.856   180.0   0.0
MOUNT C521         6 2 12 1 1   -15.844   60.656   180.0   0.0
MOUNT C108         3 2 12 1 1   -14.168   26.060   180.0   0.0
MOUNT C103         3 2 12 1 1   -12.746   26.721   270.0   0.0
MOUNT C109         3 2 12 1 1   -14.193   23.292   270.0   0.0
MOUNT C521         3 2 12 1 1   -15.844   17.856   180.0   0.0
MOUNT C103         5 3 12 1 1   -54.746   69.521   270.0   0.0
MOUNT C104         5 3 12 1 1   -56.168   69.673   0.0   0.0
MOUNT C274         3 3 12 1 1   -22.118   30.175   270.0   0.0
MOUNT C503         3 3 12 1 1   -27.376   20.498   180.0   0.0
MOUNT C520         2 3 12 1 1   -57.845   18.618   180.0   0.0
MOUNT C502         2 3 12 1 1   -71.205   19.406   180.0   0.0

AS END

sunnyzeng 2008-06-17 08:51
你的是FCM几代的机器?是BASE1吗?

菰獨寳貝 2008-06-17 11:53
是的，
2代的也是一样
我在前面说的有
你可以查看一下


查看完整版本: [-- FCMI校准问题，请高手帮助！ --] [-- top --]


Powered by PHPWind, Copyright © SMTHome.Net All rights reserved.
Time 0.105493 second(s),query:3 Gzip enabled

You can contact us